series am2lv-nz 2 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r8.c 1 of 4 north america only features: ? smd package ? operating temperatur e: -40c to +85c ? wide (2:1) input range ? regulated single/dual output ? 1500vdc isolation ? mtbf>1,000,000 hours ? continuous short circuit protection ? rohs compliant models single output model input voltage (v) output voltage (v) output current max (ma) isolation (vdc) efficiency (%) am2lv-1203s-nz 9-18 3.3 500 1500 70 am2lv-1205s-nz 9-18 5 400 1500 74 am2lv-1209s-nz 9-18 9 222 1500 76 am2lv-1212s-nz 9-18 12 167 1500 78 am2lv-1215s-nz 9-18 15 133 1500 79 AM2LV-2403S-NZ 18-36 3.3 500 1500 72 am2lv-2405s-nz 18-36 5 400 1500 76 am2lv-2409s-nz 18-36 9 222 1500 78 am2lv-2412s-nz 18-36 12 167 1500 80 am2lv-2415s-nz 18-36 15 133 1500 80 models dual output model input voltage (v) output voltage (v) output current max (ma) isolation (vdc) efficiency (%) am2lv-1205d-nz 9-18 5 200 1500 74 am2lv-1209d-nz 9-18 9 111 1500 76 am2lv-1212d-nz 9-18 12 83 1500 78 am2lv-1215d-nz 9-18 15 67 1500 80 am2lv-2405d-nz 18-36 5 200 1500 74 am2lv-2409d-nz 18-36 9 111 1500 76 am2lv-2412d-nz 18-36 12 83 1500 78 am2lv-2415d-nz 18-36 15 67 1500 80 note: unless otherwise specified, all specif ications are measured at an ambient tem perature of 25c, humidity<75%, nominal inpu t voltage and at rated output load. input specifications parameters nominal typical maximum units voltage range 12 24 9-18 18-36 vdc absolute ma ximum rating 12 24 22 40 vdc peak input voltage time 100 ms isolation specifications parameters conditions typical rated units tested i/o voltage 60 sec 1500 vdc resistance at 500 vdc 1000 mohm capacitance input to output 85 pf
series am2lv-nz 2 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r8.c 2 of 4 north america only output specifications parameters conditions typical maximum units voltage accuracy 5 % short circuit protection continuous short circuit restart auto-recovery line voltage regulation (single) from low in to high in 0.5 % load voltage regulation (single) from 10% to 100% load 1 % load voltage regulation (dual) from 10% to 100% load each output loaded within 5% of each other 5 % temperature coefficient 0.03 %/ o c ripple & noise * 20mhz bandwidth with 10% load 75 mv p-p minimum load current ** 10 % of max * test ripple & noise by ?parallel cable method? as described in application note ?ripple and nois e measurement of brick & pol dc -dc converters? available on aimtec?s website www.aimtec.com . converters are designed to operate with a minimum l oad of 10%. if converter is operated with a load less than 10% the ripple will increase. ** operation under 10% load will not damage the converte r; however, not all specifications will be met. general specifications parameters conditions typical maximum units switching frequency 100% load 300 khz operating temperature -40 to +85 o c storage temperature -55 to +125 o c maximum case temperature o c derating above 71o 2.9 %/ o c cooling free air convection humidity 95 % rh case material plastic (ul94-v0) weight 5.2 g dimensions (l x w x h) 0.94 x 0.54 x 0.32 inches 23.86 x 13.70 x 8.20 mm mtbf >1,000,000 hours (mil-hdbk -217f, ground benign, t=+25oc) maximum soldering temperature 1.5mm from case for 10 seconds 245 o c pin out specifications pin single dual 1 - vin - vin 7 nc nc 8 nc common 9 +vout +vout 10 - vout -vout 16 + vin + vin nc ? not connected
series am2lv-nz 2 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r8.c 3 of 4 north america only dimensions a 0.50 (0.02) 1.36 (0.05)max 0.50 (0.02) 5.00o angle a 23.86 (0.94) 13.70 (0.54) 7.50 (0.30) 13.10 (0.52) 15.00 (0.59) top view front view side view 8.20 (0.32) 17.50 (0.69) 1 7 8 9 10 16 23.86 (0.94) 1.02 (0.04) 0.50 (0.02) 3.04 (0.12) 2.54 (0.10) 15.24 (0.60) 18.50 (0.73) 2.54 (0.10) 15.24 (0.60) 0.80 (0.03) 2.4 (0.08) footprint
series am2lv-nz 2 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r8.c 4 of 4 north america only recommended filter circuit all the am2lv-z series have been tested with the above recommended te st circuit. this series should be tested under load. if it is necessary to further decrease the input/output ripple, the value of the filter capacitor c an be increased; a capacitor with a low esr should be used. excessive filter capacitance c an cause start up problems with the converter. in general, the recommended capacitance values are: cin: 12v input 100 f, 24v input 10 f~47 f cout: 10 f/100ma refer to table below for maximum capacitor values: external capacitor value single output vout (vdc) cout (uf) dual output vout (vdc) cout (uf) 3.3 2200 5 680 5 1000 9 470 9 680 12 330 12 470 15 220 15 330 derating note: 1. datasheets are updated as needed and as such, specifications ar e subject to change without notic e. once printed or downloaded , datasheets are no longer controlled by aimtec; refer to www.aimtec.com for the most current product specifications. 2. product labels shown, including safety agency cert ifications on labels, may vary based on the date manufactured. 3. mechanical drawings and specifications are for reference only. 4. all specifications are measured at an am bient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specifie d. 5. aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. cas numbers and other limited information are considered proprietary an d may not be available for release. 6. this product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control sys tems or other such applications which necessitate specific safety and regulatory standards ot her the ones listed in this datasheet. 7. warranty is in accordance with aimtec?s st andard terms of sale available at www.aimtec.com. dc dc + vin - vin + cin + cout + cout +vout -vout common dual output dc dc + vin - vin + cin + cout +vout - vout single output
|
